Bryan Electrical Company handles electrical work for homeowners, landlords, property managers, and businesses across Bryan, Texas. Whether you have a dead outlet that needs tracing or a full panel upgrade on the schedule, we cover residential and commercial jobs from start to finish. We are available seven days a week, from 7:30 AM to 8:30 PM, and the call for a quote is the first step.
Reach us at (979) 356-2994.
Safe wiring. Solid workmanship. Straight answers.
A flickering light and a full rewire start the same way, with someone picking up the phone and describing what they are seeing. Flickering lights, dead outlets, and breakers that trip repeatedly are the calls we field most often, and every one of them starts with the fault traced before anything is replaced.
When half a house loses power, the cause is rarely obvious from the surface. It might be a tripped breaker, a failed connection at the panel, or a wiring fault deeper in the circuit. We work through it systematically: test the circuit, check the breaker, confirm whether the problem is upstream or downstream, and explain what we found before we talk about what it costs to fix.
We also handle GFCI and AFCI diagnostics for both residential and commercial properties. A GFCI outlet that keeps tripping, or an AFCI breaker that kicks off without a clear reason, often points to a wiring condition that needs attention rather than just a reset. We find the source and take care of it. Give us a call and we will get the power back on.
Good electrical work is not complicated, it is just done right, and that applies to the smaller jobs as much as the large ones. Outlet and switch replacement, GFCI and AFCI outlet upgrades, dimmer switch installation, and ceiling fan wiring all fall under work we handle on a regular basis.
For landlords and property managers turning over units in Bryan, these are the jobs that come up most often: outlets that have stopped working, switches that need replacing, fans that need wiring or swapping out. We work through rental properties efficiently and leave the work area as it was found.
On the lighting side, we install recessed lighting, LED fixtures, and indoor and outdoor lighting for both residential and commercial spaces. Exterior and landscape lighting wiring is part of that work too, whether it is a single fixture at a front entry or a full perimeter lighting circuit for a commercial property. Call now and we will set the appointment.
Your home deserves wiring that is safe and up to code, especially when new appliances or a renovation changes what the circuits need to carry. Dryers, ovens, refrigerators, and washers each need a dedicated circuit sized for the load. Running a high-draw appliance on a shared circuit is one of the more common causes of nuisance tripping and, in some cases, a wiring hazard.
We handle wiring for kitchen remodels, bathroom remodels, and room additions, including the rough-in and finish work that brings new circuits up to current code. For older homes, we also replace knob-and-tube wiring and address aluminum branch-circuit wiring that no longer meets today's standards. A whole-home rewire is a larger project, and we walk through the scope with you so you understand what it involves before anything is scheduled.
Pricing is explained on the call and confirmed before we schedule. We keep your home powered and safe.
We know schedules shift, so we keep booking flexible, and that goes for panel work too. Breaker panel replacement, fuse box to breaker panel conversion, service entrance and meter upgrades, and subpanel installation are all work we handle for residential and commercial customers in Brazos County.
A panel inspection can tell you whether your current service capacity matches the load you are putting on it. If you are adding circuits, finishing a basement, or bringing in a new large appliance, a load calculation helps confirm whether the existing panel can carry it or whether an upgrade makes sense first.
We provide no-pressure estimates, priced up front. You get the rate on the phone before anything is put on the calendar, and you are told what the work covers. Residential wiring. Commercial wiring. One number for both.
We handle electrical work for offices, warehouses, retail spaces, apartment buildings, and multi-unit properties across Bryan and the surrounding area. Commercial electrical repair, circuit additions, outlet and panel work, and code-compliant installations are all part of what we do on the commercial side.
Property managers and landlords call us for electrical safety inspections, pre-sale and pre-purchase inspections, and code compliance work on units that need to meet current standards before occupancy or sale. Permit work is part of that process when it applies, and we handle it as part of the job.
If you manage multiple properties in Brazos County, getting electrical service scheduled without the runaround matters. We scope the work on the call and confirm pricing before anything is booked. We will make your wiring safe again.
Bryan sits in a climate that puts real demands on electrical systems. Hot, humid summers drive heavy cooling loads, severe thunderstorms roll through regularly, and the area's steady growth means older homes and buildings are often running more than their original wiring was built to handle. The three services below come up often in this area for those exact reasons.
Older homes in Bryan were wired for the loads of a different era. When air conditioning, modern appliances, and home electronics all draw from a panel that was sized decades ago, the circuits get pushed past what they were designed to carry. A panel upgrade replaces the breaker box, brings service capacity up to current levels, and ensures the wiring connections meet code. Homeowners, landlords, and commercial property owners all benefit from having a panel that matches the actual load on the system.
Brazos County storm seasons bring the kind of outages that can last well beyond a few hours. We handle the electrical side of generator connections: running the wiring, installing the transfer switch, and connecting the generator circuit to the panel so essential circuits stay live when the grid goes down. The transfer switch is what keeps the generator isolated from the utility line, and getting that installation done correctly is the part that matters most.
Lightning strikes and storm-related surges are a real risk in this part of Texas. A power strip offers limited protection at a single outlet. A panel-level surge protection device covers every circuit in the home, which means appliances, electronics, and HVAC equipment on any outlet in the building are protected when a surge comes through the line. We install whole-home surge protection at the panel as a standalone job or alongside other panel work. Call now and we will set the appointment.
Level 2 EV charger installation requires a dedicated 240-volt circuit sized for the charger and a panel with enough available capacity to support it. We confirm panel capacity on the call, run the circuit to where the charger will be installed, and handle the wiring from panel to outlet. If the panel needs work before the circuit can be added, we cover that as part of the same project. Call for a quote and the price is confirmed before we schedule.
Hard-wired smoke detectors and carbon monoxide detectors are another installation we handle regularly. Detector placement follows specific requirements based on the number of floors, the location of sleeping areas, and the presence of fuel-burning appliances. We install them to meet those requirements and wire them so the detectors communicate with each other across the home. We keep your home powered and safe.
Your home deserves wiring that is safe and up to code, and getting a straight answer on what it costs should not take more than a phone call. When you call, we go through the work with you, give you the price, and confirm what it covers before anything is scheduled. Decisions about the work get made while you are on the phone.
We are available seven days a week, from 7:30 AM to 8:30 PM. That includes weekends, and we take short-notice work when the schedule allows. Electrical service scheduled without the runaround is how we approach every call, whether it is a single outlet or a full panel replacement.
Quick response. Code-correct work. Tidy finish.
We carry out electrical work across Bryan and throughout Brazos County, including College Station, Hearne, Calvert, Madisonville, Navasota, Brenham, Caldwell, and Rockdale. If you are in the surrounding area and are not sure whether we cover your location, call and ask.
The work is done locally, scoped on the call, and priced before it is scheduled. We will make your wiring safe again.
Common signs include breakers that trip under normal loads, circuits that cannot support the appliances running on them, and a panel that has no open slots for new circuits. In Bryan, older homes that pre-date central air conditioning often have 100-amp service that no longer matches the electrical demand on the system. A load calculation on the call can help determine whether an upgrade makes sense.
A transfer switch disconnects your home from the utility grid before the generator takes over the load. Without it, a generator connected directly to the panel can back-feed power onto the utility lines, which is a hazard to anyone working on those lines during an outage. We install the transfer switch, connect the generator circuit to the panel, and test the system before the job is closed out.
Flickering can come from a loose connection at the fixture, a failing breaker, or a load on the circuit that exceeds what the wiring was sized for. Occasional dimming when a large appliance starts up is usually a load issue. Persistent flickering, dimming that affects multiple rooms, or flickering that comes with a burning smell points to a wiring or panel condition that needs attention.
Discoloration around outlets or switches, a burning smell near the panel, outlets that feel warm to the touch, breakers that trip repeatedly, and two-prong ungrounded outlets throughout the home are all signs that the wiring deserves a closer look. Knob-and-tube wiring and aluminum branch-circuit wiring carry specific risks that older homes in Bryan sometimes still have. An electrical safety inspection covers all of these conditions.
Yes. Permit work is part of the job on projects that require it, and we handle that side of the process so the work passes inspection and the documentation is in order. Whether a permit is required depends on the scope of the work and the applicable local requirements. We confirm what applies before the project starts.
Outdoor electrical work requires dry conditions at the connection points, and we confirm site conditions before starting exterior wiring jobs. Summer heat and humidity in this part of Texas also affect material choices: conduit, fittings, and outlet covers rated for exterior exposure are standard on any outdoor installation. Work that was scheduled during a storm system may need to be rescheduled for safety reasons.
The visit covers the specific fault or installation that was scoped on the call, plus anything directly related to it. For a troubleshooting call, that means testing the affected circuit, checking the relevant breaker, and tracing the fault to its source. For an inspection, the visit covers the panel, grounding and bonding, GFCI and AFCI protection, outlet and switch condition, and visible wiring throughout the home.
Breakers trip when a circuit carries more current than it was designed for, which can happen from a temporary overload or from a fault in the wiring. A breaker that trips once under a heavy load may not be a problem. One that trips repeatedly under normal conditions, will not reset, or trips immediately after resetting points to a fault in the circuit, a failing breaker, or a panel that is undersized for the load it is carrying.
A targeted repair is appropriate when the fault is isolated and the surrounding wiring is in good condition. When the problem is a symptom of wiring that has deteriorated throughout the home, patching around it leaves the underlying issue in place. We explain what we find and what the options are, including when a more complete repair is the more practical answer.
A full panel replacement involves removing the existing breaker box, installing a new panel sized for the current and anticipated load, reconnecting the circuits, and confirming that the work meets code before the panel is energized. If the service entrance needs upgrading at the same time, that is part of the same project. We walk through the scope and the price on the call before any work is scheduled.
The scoping process starts on the call with the description of what you are seeing or what you need. On site, we test the affected circuits, inspect the panel, and look at the wiring condition in the area of the fault. The scope is confirmed before work begins, and if the visit turns up something that changes the picture, that conversation happens before the work expands.
Bryan Electrical Company is available seven days a week, from 7:30 AM to 8:30 PM.
Call (979) 356-2994 to get a quote on any residential or commercial electrical job in Bryan or the surrounding Brazos County area.
We go through the work with you on the call, give you the price, and confirm the schedule before anything is set.
Safe wiring. Solid workmanship. Straight answers.
Below is a plain-language look at the electrical work we handle for homes, rentals, and commercial properties in Bryan and across Brazos County. Each row covers what the service includes, who it fits best, and one practical note worth knowing before you call. If a job you need is not listed, call us and we will talk through it.
| Service Type | What the Job Involves | Common Situations | Good to Know |
|---|---|---|---|
| Electrical Panel and Service Upgrades | Panel replacement and sizing, 100 to 200 amp service upgrade, Subpanel installation, Load calculation before upgrade | Older homes in Bryan adding AC, appliances, or new circuits that the existing panel cannot support | In Bryan, homes built before central air conditioning was standard often carry 100-amp service that no longer matches the load on the system. A load calculation on the call helps confirm whether an upgrade is the right next step. |
| Ceiling Fan Installation | Fan wiring and mounting, Switch and remote wiring, Fan replacement on existing boxes, New ceiling box installation | Homeowners adding or replacing ceiling fans in any room | Fans require a ceiling box rated for fan weight and motion. If the existing box is not rated, we replace it as part of the installation. |
| EV Charger Installation | Level 2 charger circuit wiring, 240-volt outlet installation, Panel capacity check before install, Panel upgrade coordination if needed | Homeowners adding an electric vehicle and needing a reliable home charging setup | We confirm panel capacity on the call before scheduling. If the panel needs work to support the new circuit, we cover that as part of the same project. |
| Electrical Safety Inspections | Panel and grounding check, GFCI and AFCI coverage review, Outlet and wiring condition assessment, Pre-sale and pre-purchase inspections | Homeowners, buyers, landlords, and property managers who need a clear picture of the electrical condition before a transaction or occupancy | An inspection covers the panel, grounding and bonding, protection device placement, and visible wiring throughout the home. The findings are explained on site. |
| Dedicated Appliance Circuits | Dryer and oven circuit runs, Refrigerator and washer circuits, Workshop and garage circuits, Load sizing before install | Homeowners adding a major appliance or a high-draw workspace that needs its own circuit | Running a high-draw appliance on a shared circuit is one of the more common causes of nuisance tripping. A dedicated circuit sized to the load solves it at the source. |
| Backup Generator Installation | Transfer switch installation, Generator circuit wiring, Panel connection and testing, Essential circuit hookup | Bryan and Brazos County homeowners who need reliable power through storm-season outages | The transfer switch is what isolates your home from the utility line during an outage. Getting that installation done correctly is the part that matters most for safety and code compliance. |
| Wiring and Circuit Installation | New circuit runs, Rough-in and finish wiring, Older wiring replacement, Whole-home rewiring | Homes with outdated wiring, properties undergoing renovation, or any space that needs new circuits added | Knob-and-tube and aluminum branch-circuit wiring both carry specific risks that come up in older Bryan homes. We address both and walk through the scope before any work begins. |
| Lighting Installation | Recessed and LED fixture install, Indoor and outdoor lighting, Exterior and landscape circuit wiring, Commercial fixture installation | Homeowners upgrading interior lighting or adding exterior coverage, and commercial properties needing code-compliant fixture work | Exterior lighting wiring in Bryan needs to account for heat and humidity. Conduit, fittings, and outlet covers rated for outdoor exposure are standard on any exterior installation we do. |
| Whole-Home Surge Protection | Panel-level surge device installation, Full-home circuit coverage, Standalone or combined with panel work, Protection for appliances and electronics | Bryan homeowners in areas with frequent lightning or storm-related power surges | A panel-level surge protection device covers every circuit in the home. A power strip only protects the outlets plugged into it, leaving everything else on the system exposed. |
| Outlet and Switch Installation | Outlet replacement and upgrade, GFCI and AFCI outlet installation, Dimmer switch wiring, Switch replacement | Homeowners, landlords, and property managers updating or repairing outlets and switches | GFCI outlets in kitchens, bathrooms, garages, and outdoor areas are a code requirement in most installations. We confirm placement meets current requirements. |
| Older-Home Rewiring | Knob-and-tube removal and replacement, Aluminum branch-circuit remediation, Grounding updates, Full or partial rewire scoping | Owners of older Bryan homes whose wiring no longer meets current standards or shows signs of deterioration | A whole-home rewire is a larger project and we walk through the full scope with you before anything is scheduled, so you understand what is involved and what it covers. |
| Electrical Repairs and Troubleshooting | Dead outlets traced to source, Flickering light diagnosis, GFCI and AFCI fault finding, Circuit testing and confirmation | Any home or property with an unexplained electrical fault | The fault is traced before anything is replaced, so you are not paying to swap parts that were not the problem. |
| Breaker and Fuse Repair | Breaker testing and replacement, Fuse box diagnosis, Panel connection checks, Repeated-trip investigation | Homeowners dealing with breakers that will not hold or a fuse box that keeps causing problems | A breaker that trips immediately after reset often points to a fault in the circuit, not just the breaker itself. We check both. |
| Wiring for Additions and Remodels | Kitchen and bathroom remodel wiring, Room addition rough-in, Code-compliant finish wiring, Circuit updates for new layouts | Homeowners remodeling or adding space who need electrical brought up to current code | Remodel wiring often uncovers conditions in the existing circuits that need attention. We explain what we find before the scope expands. |
How do I know if my home is ready for the electrical load I want to add?
The starting point is a load calculation, which compares what the panel is rated to carry against what the circuits are already drawing. If you are adding a large appliance, an EV charger, or finishing a room, that calculation tells us whether the existing panel has capacity or whether an upgrade needs to happen first. We go through this on the call before anything is scheduled.
What is the difference between a GFCI outlet and an AFCI breaker, and do I need both?
A GFCI outlet detects ground faults and cuts power to prevent shock. It is required in kitchens, bathrooms, garages, and outdoor areas. An AFCI breaker detects arc faults, which are the kind of wiring condition that can start a fire inside a wall before anything trips. Current code requires AFCI protection in most living spaces in new construction and in circuits that are being replaced or extended. Whether your home needs one, the other, or both depends on when it was built and what work is being done. We confirm what applies before the work starts.
Can I add a workshop or garage circuit without upgrading the whole panel?
Sometimes yes, sometimes no. It depends on how many open slots the panel has and what the existing load looks like. A workshop circuit for a table saw or a compressor draws a meaningful amount of current, so we check panel capacity before running the circuit. If there is room and the service size supports it, we add the circuit without touching the panel. If not, we explain the options and what each one involves.
Faults Traced Before Anything Is Replaced
We work through the circuit systematically and confirm the source of the problem before any parts come out. That keeps the repair focused on what actually caused the fault.
What is involved in connecting a backup generator to the home?
The electrical side of a generator connection includes running the wiring from the generator location to the panel, installing a transfer switch, and connecting the essential circuits you want the generator to cover. The transfer switch is the critical part. It disconnects the home from the utility line before the generator takes over, which prevents back-feed onto the utility lines during an outage. We install and test the transfer switch as part of every generator hookup.
Why does my outlet feel warm, and is that a problem?
An outlet that feels warm to the touch is worth taking seriously. It can point to a loose connection, a wiring condition that is generating heat, or a circuit that is carrying more load than it was sized for. Warmth at an outlet, buzzing sounds near the panel or a switch, or discoloration around a cover plate are all signs that something needs a closer look. We trace the condition to its source rather than assume it is minor.
How does surge protection at the panel differ from using surge-protecting power strips?
A power strip with surge protection covers only the devices plugged into it. Everything else in the home, appliances, electronics, and equipment on any other outlet, is still exposed. A panel-level surge protection device sits at the main panel and covers every circuit in the building. In Bryan, where lightning and storm-related surges are a real seasonal risk, panel-level protection is the more complete answer. We install it as a standalone job or alongside other panel work.
Code-Compliant Work on Every Job
Permit work is handled as part of the project when the scope requires it. The work is done to the standards the local inspectors enforce, and we confirm what applies before the job starts.
When does an electrical problem call for a full rewire rather than targeted repairs?
A targeted repair makes sense when the fault is isolated and the surrounding wiring is in good condition. When the problem keeps coming back, shows up in multiple rooms, or the wiring is knob-and-tube or deteriorated aluminum branch-circuit wiring throughout the home, patching around it leaves the underlying condition in place. We explain what we find and what the options are, including when a more complete approach is the more practical answer for the long run.
What does Level 2 EV charger installation actually involve?
A Level 2 charger runs on a dedicated 240-volt circuit, the same voltage as a dryer or an oven. We run a circuit from the panel to where the charger will be mounted, install the outlet or hardwire the charger depending on the unit, and confirm that the panel has enough available capacity to support the added load. If the panel needs an upgrade before the circuit can be added, we handle that as part of the same project. The price for the full scope is confirmed on the call before anything is scheduled.
Scope Agreed Before the Panel Is Opened
The price and the scope are confirmed on the call before anything is scheduled. If the visit turns up something that changes the picture, that conversation happens before the work expands.
What are the risks of aluminum branch-circuit wiring in older homes?
Aluminum branch-circuit wiring was used in residential construction during a period when copper prices were high. Over time, aluminum connections can loosen and oxidize in ways that create resistance and heat at the connection points. Outlets, switches, and fixtures connected to aluminum wiring need to be rated for aluminum, or the connections need to be made with approved connectors. We assess the condition of aluminum wiring during an inspection and explain the remediation options before any work is done.
How do I get an estimate for electrical work, and what does the pricing process look like?
The estimate starts on the call. We go through what you are seeing or what you need, ask enough questions to scope the job, and give you the price before anything is put on the calendar. You are told what the work covers and what it costs. No-pressure estimates, priced up front, is how we handle every call, whether it is a single outlet or a full panel replacement.
Is hard-wired smoke detector placement something an electrician handles?
Yes. Hard-wired smoke and carbon monoxide detectors need to be placed according to requirements based on the number of floors, the location of sleeping areas, and the presence of fuel-burning appliances. We install them to meet those requirements and wire them so the detectors communicate with each other across the home. If you are replacing battery-operated detectors with hard-wired ones, or adding detectors to meet current code, we handle the wiring and placement as part of the same job.
Call (979) 356-2994 and we will go through the work with you, give you a straight answer on what it involves, and confirm the price before anything is set.
(979) 356-2994